ACP+ (Amp Camp Pre-Amp + Headphone Amp)
This is the ACP+ (Amp Camp Pre-Amp + Headphone Amp) PCB, as built at Burning Amp Festival in 2019.
The pre-amp PCB is available for purchase by itself (gold traces, 2oz copper).
A ground plane is also available for purchase so that you can build it naked just like they did at BAF (if you're into that kind of thing).
If you would like to purchase both the pre-amp board and the ground plane, please add both items to your cart.
Both boards are 8" (W) x 6.5” (L) or 203.2mm (W) x 165.1mm (L).
Parts Kit ($179)
This kit of 122 parts across 48 line items includes everything you need to build a "naked" ACP+ ("naked" meaning there is no chassis).
Notably it includes the matched quad of Toshiba 2SJ74-GR JFETs as well as an alps "Blue Velvet" potentiometer.
Please see note below about the parts used in the photographs on this page.
Full Naked Kit Bundle ($199)
A full kit bundle includes the pre-amp PCB, ground plane PCB, parts kit, and JFETs.
Photos of Poet's DIY ACP+
The photo of a built-up ACP+ (taken by Thuss and Farrell) is shown to demonstrate what a completely do-it-yourself ACP+ with a colorful parts selection can look at.
The parts shown in that photo were all chosen, stuffed and soldered by Patrick Farrell's 10 year old daughter, Poet.
It did not use the parts kit sold on this page. Please refer to the parts kit photo to see what's included in the parts kit. Notably, the knob shown is a silver anodized aluminum knob from Patrick's spare-parts drawer, which was then spray painted gold by hand. This is do-it-yourself audio, let your imagination run wild.
Just finished it. No issues, all went to together well, and tested well. I followed Nelson's guide and also looked at 6L6's guide and I am still going through the blog to see what adventures others are having building this. I am not an electronic engineer but I will give advice if I can, but most members beat me to it...
Ended up using a Meanwell 24v 2.2A internal smps for the power supply, and as I intend leaving it on most of the time, this is probably best best choice from a power bill point of view these days.
Although I may try a linear supply later to see if it makes any difference in the sound. My B1K uses a linear supply as does an AMB M3 I built as a headphone amp, both are truly great sounding devices. The ACP+ sounds good too, just different, not sure which I like more at this point . Still to try the ACP+ as a preamp yet into my DIY Akatika power amp, that's in a another room, just enjoying it as a headphone amp at the moment. Oh, and I should mention I'm not normally a classical music fan, but I accidentally came across a bit on DAB radio and it sounded very good, so I would suggest classical fans should defiantly check this amp out.
Next up, I will have to build a box for it... that gold knob has got me imagination think'in...
Two weeks later: Box is built as per photos, no gold knob yet, can't get the paint due to lock down, hoping to soon though, but I think it looks good as a piece of serious hi fi just for the moment.
Perfect sales good that i bayed this unit great Sound
topp on my Rotel Amp RB 1090 and together with my Titan Quadral speakers
compliments to the DIY staff :))) kind regards Georg Pass fan....
This is a very nice headphone amplifier indeed. It sounds terrific. Many thanks to Nelson Pass and the diyaudio community!
I built mine with the recommended components, except for the decoupling capacitor at the entry, which consists of two 4u7 capacitors in parallel. The heatsinks are hovering above the MOSFETs on a piece of alumininiun u-profile The case is made from scrap aluminium sheet welded together with Durafix.
The power source source is from an 2 * 12V Amplimo toroid transformer and a series of 1500uF smoothing capacitors. It's then followed by a super-regulator for which I built my own PCB.
I built the ACP+ and was very curious if it will beat Waynes LineStage and the B1 Korg NUTUBE-pre?
There is no winner! Built them all! The ACP+ is a very good sounding preamp. I like it especially as a headphoneamp.
The pcb is well made and big size. Add to buy a matched set of P-channel-JFets (LinearSystems) from
the DIYaudiostore and you have a very good basis for an excellent sounding preamp.
Thanks to Nelson Pass to offer this design to the community!
Thanks to the DIYaudiostore -team for the perfect service! Super fast delivery!!!
Great design, layout and board. I’ve been spending more time with ACP than any of my other pre’s - it sounds fantastic. Probably the best HPA I’ve heard too.
Great headphone amp haven't used the pre amp function yet. Whammy amp next.
Love it. Am amazed at how quiet it is; With headphones or horn loudspeakers, I can hear no hum or noise -- unlike my now former receiver or preamp. Sounds great, too. Many thanks to Nelson Pass. Only fly in the ointment was that the wrong power supply was sent in the kit, and it took about a month to receive the correct one. Otherwise, all is well.
Anyone wishing to start in DIY, this is 'THE" amp kit to try.
You can put it together in an hour or so...ok maybe 2-3 hours...
Simple elegant and the naked look IMO is so awesome.
And it works well and drives most headphones decently.
If your hesitating and want to learn the basics, soldering etc...this is a wonderful choice!
We Also Recommend